Departman za proizvodno mašinstvo

Statistika Imејl upоzоrеnjе RSS Feed
Organization name
Departman za proizvodno mašinstvo
Parent OrgUnit
City
Novi Sad
Country
Serbia

OrgUnit's Researchers publications
(Zаmеnik/rаdnа grupа izdаnjа)

Rеzultаti 81-100 оd 376 (Vrеmе prеtrаgе: 0.005 sekundi).

Dаtum izdаvаnjаNаslоvАutоr(i)
811-јан-2014Dependence of interfacial heat transfer coefficient on casting surface temperature during solidification of Al-Si alloy castings cast in CO2 sand moldKovačević, Lazar ; Terek, Pal ; Miletić, Aleksandar; Kakaš D.
821-јул-2019Design and Fabrication of Ferrite Inductor Using 3D Printed Spiral Coil and Ferrite DiscMenicanin A.; Lukovic M.; Blaz N.; Movrin, Dejan ; Zivanov L.
831-јан-2012Design of casting blanks in CAPP system for parts of piston-cylinder assembly of internal combustion enginesTodić, Vladimir ; Tepić J.; Milošević M.; Lukić D.; Hadžistević, Miodrag 
841-јан-2019Design of custom made prosthesis of the hipTabaković, Slobodan ; Zeljković, Milan ; Milojević, Zoran ; Živković, Aleksandar 
851-јан-2013Determination of surface roughness and topography of dental resin-based nanocomposites using AFM analysisTijana Lainović ; Marko Vilotić ; Larisa Blažić ; Damir Kakaš; Dubravka Marković ; Aljoša Ivanišević
8615-мај-2005Development of a programme system for data-point pre-processing in Reverse EngineeringBudak, Igor ; Hodolic J.; Sokovic M.
871-јул-2017Development of an expert system for the simulation model for casting metal substructure of a metal-ceramic crown designMatin I.; Hadžistević, Miodrag ; Vukelić, Đorđe ; Potran M.; Brajlih T.
881-јан-2016Development of banded microstructure in 34CrNiMo6 steelNagode A.; Resnik A.; Bizjak M.; Kosec G.; Karpe B.; Budak, Igor ; Kosec B.; Zorc B.
891-јан-2019Development of expert system for the selection of 3d digitization method in tangible cultural heritageBudak, Igor ; Santoši, Željko ; Stojaković, Vesna ; Korolija - Crkvenjakov, Daniela ; Obradović, Ratko ; Milošević, Mijodrag ; Šokac, Mario 
901-дец-2017The Difference Between GUM and ISO/TC 15530-3 Method to Evaluate the Measurement Uncertainty of Flatness by a CMMŠtrbac, Branko ; Radlovački V.; Spasić-Jokić V.; Delić, Milan; Hadžistević, Miodrag 
911-јан-2015Different Approaches in Uncertainty Evaluation for Measurement of Complex Surfaces Using Coordinate Measuring MachineVrba I.; Palencar R.; Hadžistević, Miodrag ; Štrbac, Branko ; Spasic-Jokic V.; Hodolic J.
921-јан-2019Dimensional errors in selective laser melting products related to different orientations and processing parametersPal, Magdolna; Kokol V.; Gubeljak N.; Hadžistević, Miodrag ; Hudak R.; Drstvensek I.
931-јан-2020Dual Phase Austempered Ductile Iron - The Material Revolution and Its Engineering ApplicationsEric Cekic O.; Rajnović, Dragan ; Sidjanin L.; Janjatović, Petar ; Baloš, Sebastian 
941-мар-2017A Ductile Fracture Criterion of Ti-6Al-4V at Room TemperatureVilotić, Dragana; Movrin, Dejan ; Alexandrov S.
9516-мар-2012Duplex hard coatings with aditional ion implantationŠkorić, Branko ; Kakaš D.; Favato G.; Miletić A.; Arsenović, Marko 
9620-јан-2018Eco-design of a low-cost adsorbent produced from waste cherry kernelsVukelić, Đorđe ; Boškov, Novak ; Agarski, Boris ; Radonić, Jelena ; Budak, Igor ; Pap, Ištvan; Turk-Sekulić, Maja 
971-мар-2019Eco-design of fixtures based on life cycle and cost assessmentVukelić, Đorđe ; Agarski, Boris ; Budak, Igor ; Simunovic G.; Buchmeister B.; Jakovljevic Z.; Tadic B.
981-феб-2017The economic sustainability of a model that balances ecological and power supply needsKirin S.; Kovac P.; Savković, Borislav ; Mirjanic S.; Soos L.
9917-јун-2013Effect of austempering temperature on cavitation behaviour of unalloyed ADI materialDojcinovic M.; Eric O.; Rajnović, Dragan ; Sidjanin L.; Baloš, Sebastian 
1001-јан-1997Effect of Azotobacter strains on sugar beet callus proliferation and nitrogen metabolism enzymesMezei S. ; Popović M.; Kovačević, Lazar ; Mrkovački N.; Nagl N.; Malenčić, Đorđe